Welcome to the EJ500 timer guide. Follow these instructions for setup, wiring, and operation. Ensure proper voltage and battery placement for reliable performance. Use LED display to confirm settings
1.1 Overview of EJ500 Timer
Designed for residential and commercial use, the EJ500 timer offers a versatile solution for controlling lighting, HVAC, and other electrical loads. It supports 500 W single‑gang or 2‑gang installations, with a minimum 40 W rating and 4 A current capacity for tungsten or inductive ballast lamps. Operating at 120 VAC, 60 Hz, the unit maintains a temperature range of 0 °C to 40 °C, ensuring reliable performance in typical indoor environments. The timer’s compact 2‑inch housing houses a bright LED display that shows time, mode, and status, while four tactile buttons allow users to set schedules, switch modes, and reset the device. Battery life is extended by using two LR44 or SR44 cells, and the unit includes a dedicated battery compartment for easy replacement. The EJ500 also features a self‑adjusting mode that compensates for daylight variations, and a fixed schedule mode for consistent operation. Firmware updates can be applied via the manufacturer’s website, providing new bug, fixes.
1.2 Key Features
• 500 W single‑gang or 2‑gang rating with a 40 W minimum load and 4 A current capacity for tungsten or inductive ballast lamps. • 120 VAC, 60 Hz operation with a 0 °C‑40 °C temperature envelope for indoor use. • Compact 2‑inch housing contains a bright LED display that shows time, mode, and status, and four tactile buttons for setting schedules, switching modes, and resetting the unit. • Two LR44/SR44 batteries in a dedicated compartment provide long‑lasting power and easy replacement. • Self‑adjusting mode compensates for daylight variations, while fixed‑schedule mode delivers consistent operation. • Firmware updates are available through the manufacturer’s website, allowing users to download the latest version, open the timer’s control panel, navigate to Settings, select Software Update, and follow on‑screen instructions to upload the new firmware. • Designed for residential and commercial lighting, HVAC, and other electrical loads, the EJ500 timer offers reliable performance and user‑friendly operation. It also supports remote control via an app!!

Setup and Installation
Install the EJ500 by connecting LINE to TIMER BLACK and LOAD to TIMER BLUE. Power on, LED flashes 12:00 AM; press NEXT/ON/OFF to start. Use two LR44 batteries. Follow wiring diagram. Test mode ready.Done!

2.1 Power Requirements
The EJ500 timer operates on standard 120 VAC at 60 Hz, drawing a maximum of 4 A. It is rated for 500 W loads, with a minimum of 40 W, and is approved for use in single‑ or dual‑gang wall boxes. The unit’s internal circuitry requires a stable line voltage, ensuring reliable performance for optimal operation and safety. For standby power, the timer uses two LR44 or SR44 button‑cell batteries, which provide the low‑current logic drive when the mains supply is disconnected. The device is engineered to support incandescent, halogen, and Class P ballast fluorescent lamps, but not high‑intensity discharge or LED fixtures without proper ballast. When installing, verify that the line and load conductors are correctly connected to the TIMER BLACK and TIMER BLUE terminals, respectively, and that the neutral is tied to the TIMER WHITE. Proper grounding is essential for safety and to prevent electrical noise. The timer’s power consumption is negligible during off cycles, making it ideal for energy‑saving schedules. Now!!!
2.2 Wiring Connections
To wire the EJ500, first turn off the circuit breaker. Strip the ends of the line, load, and neutral wires. Twist the line wire from the wall into the TIMER BLACK terminal, ensuring a snug fit. Twist the load wire into the TIMER BLUE terminal, again securing it tightly. Connect the neutral wire to the TIMER WHITE terminal. If the device has a ground screw, attach the grounding wire to it. Use wire nuts or twist connectors for all splices. After all connections are secure, replace the cover plate and restore power. Verify that the timer’s LED displays “MAN” mode before setting schedules. This wiring method complies with the manufacturer’s safety guidelines and ensures reliable operation. are, tight to prevent arcing.
Ensure that the line and load are correctly identified; the line should be the hot feed, and the load should be the device you wish to control. Use a multimeter to confirm continuity before restoring power. If the timer has a ground screw, attach the grounding wire securely.
After wiring, test timer MAN mode observing LED. If LED does not flash, double‑check the line and load connections for polarity. Replace loose contacts!

Physical Components
The EJ500 timer features a robust housing, a dedicated battery compartment, and a LED display. The housing protects circuits,in while the battery compartment houses two LR44 batteries for backup power.
3.1 Timer Housing
The EJ500 timer housing is a rugged plastic shell designed for durability and safety. Rated for 0 °C to 40 °C, it handles 120 VAC, 60 Hz input and supports up to 500 W per channel. The enclosure features a vented design that dissipates heat from internal components, preventing thermal buildup. A recessed front panel protects the LED display and control buttons, while a secure latch keeps the unit firmly in place. The matte paint resists fingerprints and minor scratches, maintaining a clean look. A dedicated battery compartment houses two LR44 or SR44 cells, sealed against dust for backup power during outages. Overall, the housing balances robust construction with user‑friendly features, making the EJ500 reliable for residential and commercial timer use. The housing also incorporates a secure mounting bracket with pre‑drilled holes for screws, ensuring a stable installation on any wall surface. Its lightweight design allows easy handling during installation and maintenance. It also features a tamper‑proof seal for added security.
3.2 Battery Compartment
The EJ500 timer contains a dedicated battery compartment that holds two LR44 or SR44 button cells. These small, coin‑type batteries provide backup power when the main line is interrupted, ensuring the timer’s settings and LED display remain intact during outages. The compartment is sealed with a removable cover that can be opened by a small Phillips screwdriver. Inside, a spring‑loaded latch holds the batteries in place, preventing accidental dislodgement. The cover is marked with a battery symbol and a warning to use only the specified battery types to avoid damage. When replacing the batteries, first turn off the device and disconnect the power source. Remove the cover, insert fresh LR44 or SR44 cells with correct polarity, and replace the cover securely. The compartment’s design allows quick access while protecting the internal circuitry from dust and moisture. Proper battery maintenance extends the timer’s operational life and guarantees reliable performance. All functions are fully automated, providing peace of mind!.
LED display shows time, mode, and status. Three buttons: next, on/off, reset. Display flashes to indicate mode changes. LED stays lit during operation. Use clear markings for quick access. for users!!!
4.1 LED Display Functionality
The EJ500’s back‑lit LED panel provides real‑time feedback on all operational states. When the timer powers up, the display flashes “12:00 AM” until the user presses the NEXT/ON/OFF button, after which it toggles between “ON” and “OFF” to confirm the current mode. During normal operation the LED remains illuminated, cycling through the set time, the selected mode (MAN, FIX, or SELF), and a status indicator that flashes when a mode change is pending. The display also shows the battery status when the power is low, allowing the user to replace the two LR44/SR44 cells before the timer loses power. All characters are back‑lit for visibility in low‑light conditions, and the panel’s brightness automatically adjusts to ambient light to reduce eye strain. By reading the LED output, users can verify that the timer is correctly scheduled, that the self‑adjusting mode is active, and that the power supply is stable.life.The LED also dims after 30 minutes of inactivity, conserving battery life and power.
4.2 Button Functions
The EJ500’s single multifunction button, labeled NEXT/ON/OFF, is the primary interface for all timer operations. A short press (under 2 seconds) cycles the LED between ON and OFF states, while a longer press (2–4 seconds) switches to the next mode—MAN, FIX, or SELF. In MAN mode, the button allows manual time entry by incrementing hour and minute digits; a double‑tap resets the timer to factory defaults. In FIX mode, the same button sets the start and end times, and in SELF mode it locks the schedule, letting the timer auto‑adjust to ambient light. The button’s tactile feedback and subtle click sound confirm each action, aiding use in low‑light environments. Its internal micro‑switch is rated for 10,000 cycles, ensuring durability over a 10‑year lifespan. Firmware updates can adjust the button’s sensitivity thresholds, allowing advanced users to fine‑tune press durations for faster or slower mode changes. The button’s design supports quick adjustments during installation, making the EJ500 intuitive for both novice and experienced installers. All functions!.

Setting the Time
Set time by pressing NEXT/ON/OFF to enter MAN mode, then use the button to increment hours and minutes. Confirm with LED, then press NEXT to exit. Battery power required Ensure correct AM/PM setting
5.1 Time Mode Configuration
To configure the EJ500 time mode, first power the unit with its two LR44/SR44 batteries. The LED display will flash 12:00 AM, indicating the timer is ready. Press the NEXT/ON/OFF button to switch into manual (MAN) mode. The display will show the current hour; use the same button to cycle through hours from 01 to 12. After selecting the hour, press NEXT again to lock it and advance to minutes. The LED will now show the programmed time, and the timer will begin counting based on the selected schedule. If the time is set incorrectly, repeat the process. Remember to set AM/PM correctly; the timer does not automatically detect daylight saving changes. The EJ500’s manual time entry feature is designed for quick adjustments, making it ideal for users who need to change lighting schedules frequently. This mode is essential for ensuring that the timer’s ON/OFF cycles align with household routines or energy‑saving plans. By following these steps, you can reliably program the EJ500 to match your daily lighting needs!
5.2 Manual Time Entry
To verify the programmed time, observe the LED display during the countdown; it blinks each minute. If the timer stalls, press NEXT to reset. Holding NEXT for 3 s toggles AM/PM,output. Ensure batteries are seated; connection properly can lose the schedule.

Scheduling Modes
Choose Fixed or Self‑Adjusting. Fixed sets a daily on/off time; Self‑Adjusting syncs with sunrise/sunset. Use NEXT to cycle modes, then set times via LED. Adjust as needed fast.

6.1 Fixed Schedule
The Fixed Schedule mode on the EJ500 allows users to set a precise on/off cycle that repeats daily. To activate this mode, press the NEXT button until the LED display shows “MAN” or “MAN mode.” Once in manual mode, use the ON/OFF button to toggle between setting the start time and the end time. The timer will then run from the start time to the end time each day, ignoring daylight changes. This is ideal for appliances that require consistent operation, such as HVAC units, kitchen lights, or security systems. If you need to change the schedule, simply press NEXT to return to manual mode, adjust the times, and confirm by pressing ON/OFF again. The EJ500 will store the new schedule in non‑volatile memory, ensuring it persists after power loss. For troubleshooting, ensure the battery is fresh, the wiring is correct, and the timer is not in self‑adjusting mode. The fixed schedule is a reliable way to automate daily tasks without manual intervention. Use LED to confirm settings now! Thanks!
6.2 Self-Adjusting Mode
The Self‑Adjusting mode on the EJ500 automatically adapts to actual load times. To enable it, press NEXT until the display shows “MAN,” then press ON/OFF to toggle into manual mode. Set the desired on/off times; the timer will adjust to maintain a consistent cycle length regardless of daylight or power fluctuations. This mode is ideal for devices with variable duty cycles such as HVAC units, kitchen lights, or security systems. Wiring instructions: connect the LINE wire from the wall to the TIMER BLACK wire with a twist connector, and the LOAD wire to the TIMER BLUE wire. The battery compartment holds two LR44/SR44 cells. After setting, press ON/OFF to lock the schedule. The timer will remember the configuration across power cycles. For firmware updates, visit the Intermatic website and follow the on‑screen instructions. Use the LED display to confirm settings. If problems arise, check the battery, wiring, and ensure the self‑adjusting feature is selected. This feature keeps your appliances running on a schedule.

Timer Operation
The EJ500 cycles ON/OFF per set times. Press ON/OFF to start; LED shows status. Use manual override to pause; press ON/OFF again to resume. The timer logs cycles for monitoring. Save power, cut cost

7.1 ON/OFF Cycles
The EJ500 timer executes scheduled ON/OFF cycles based on user‑defined start and stop times. When the timer reaches the programmed start time, the LED lights green, and the connected load receives power. At the programmed stop time, the LED turns red, and the load is de‑energized. Users can toggle between “ON” and “OFF” manually by pressing the ON/OFF button, which temporarily overrides the schedule until the next scheduled event. The timer’s internal clock maintains accurate time even after power loss, thanks to the backup battery. Each cycle is logged in the internal memory, allowing the user to review operation history via the display. Proper operation requires correct wiring: LINE to BLACK, LOAD to BLUE, and a stable 120VAC supply. The timer’s firmware automatically manages power‑saving modes, ensuring minimal energy consumption during OFF periods. For safety, always verify the device is rated for the load’s wattage. Ensure the timer’s firmware is updated for performance safety
7.2 Manual Override
When the EJ500 timer is in operation, a user may temporarily bypass the programmed schedule by pressing the ON/OFF button. This manual override turns the load on or off regardless of the set times. The LED indicator flashes to confirm the override state. The timer remains in this state until the next scheduled event or until the user presses the button again to return to automatic mode. The override does not alter the internal clock or the programmed cycle; it merely provides a quick way to control lighting during emergencies or special occasions. After the override, the timer resumes normal cycling at the next scheduled start time. Users should avoid leaving the override active for extended periods to prevent unintended power consumption. The manual override feature is designed to be intuitive and requires additional configuration. For safety, ensure the load does not exceed the rated 500 W capacity. Firmware updates may refine override behavior, so keep the unit’s software current!!!

Maintenance and Troubleshooting Instructions
Check battery life, replace LR44 if dimming. Inspect wiring for loose connections. If timer fails, reset by unplugging for 30s. Update firmware via Intermatic site. Contact support if issues persist.
8.1 Battery Replacement
Replace the two LR44/SR44 button cells when the LED indicator turns dim or the timer stops responding. Open the back panel by removing the two screws on the rear edge. Gently lift the cover and locate the battery tray. Remove the old batteries, noting the polarity marks. Insert fresh LR44/SR44 cells with the positive side up. Re‑attach the cover and secure the screws. Test the timer by pressing the ON/OFF button; the LED should flash to confirm power. If the timer still does not operate, double‑check the battery orientation and ensure the contacts are clean. For long‑term reliability, replace the batteries every 12–18 months or sooner if the LED shows a weak glow.
Use a cotton swab lightly moistened with isopropyl alcohol to clean contacts. After replacement, test the timer. If the LED remains dim, replace the batteries again. Keep spare batteries in a cool dry place. Do not use rechargeable cells.
Store spare batteries in a cool, dry place to maintain optimal performance.!!
8.2 Firmware Updates
To keep your EJ500 running smoothly, update its firmware regularly. Begin by visiting Intermatic’s official website and locate the latest firmware for the EJ500 model. Download the update file to a computer that is connected to the same network as the timer. Power the timer and open its control panel via the small button on the front. Navigate to the Settings menu, then select “Software Update.” Follow the on‑screen prompts to upload the downloaded file. The timer will reboot automatically once the update is complete. Verify the firmware version in the status screen to confirm the update succeeded. If the timer fails to respond, reset it by removing the batteries for 30 seconds, then re‑install them and retry the update process. Keep the firmware file saved for future use. After the update, the timer’s LED will flash to indicate success. If errors occur, consult the troubleshooting guide or contact Intermatic support. Keep firmware current for performance gains. and updates. daily.!